News

How much joint displacement can the TPE band withstand?   There are two types of TPE band: ordinary TPE band and mesh TPE band. Due to their different structures, their ability to withstand seam displacement is also different.   There is a significant difference in the ability of ordinary TPE band and mesh TPE band to withstand seam displacement. Mesh TPE band is designed specifically to cope with large displacement, and its performance far exceeds that of ordinary TPE band.     The core differences between the two are as follows:   Characteristics Ordinary TPE band Mesh TPE band Displacement capability Suitable for small to medium displacement. Can withstand displacements of 5mm and 10mm.   Can withstand significant displacement. Capable of handling cyclic displacements ranging from ± 25% to ± 50% of joint width. Core Advantages Seal by relying on the elasticity of the material itself.   Built in high-strength polyester mesh, like a "skeleton", bears the main tensile force. tensile strength Limited, prone to necking (local thinning) when subjected to tension.   Improve by 30%~50% or more, not easily broken. Tear resistance Easy to be pierced or torn by sharp objects.   The grid can effectively prevent the expansion of tearing cracks and has stronger resistance to puncture and tearing. Creep resistance Easy to relax and deform under long-term stress.   Grid can limit the sliding of molecular chains, resulting in smaller permanent deformation and better elastic recovery. Application Scenarios Small displacement building joints, such as small prefabricated panel joints, wall cracks, etc.   Dynamic joints with large displacement, such as bridges, tunnels, underground pipe galleries, etc.     ◉  Ordinary TPE band: Its displacement capability is usually measured in millimeters. It relies on the elasticity and flexibility of the material itself to adapt to changes in the joint. When the joint displacement exceeds its bearing range, it is prone to tearing or failure due to excessive stretching.   ◉  Mesh TPE band: Its displacement capability is measured as a percentage of the seam width. The internal polyester mesh not only significantly improves tensile strength, but also enhances tear and creep resistance, making it an ideal choice for large displacement and high demand engineering scenarios.   The choice of TPE band depends entirely on your project requirements: •  If the seam displacement is within 10mm, a qualified ordinary TPE tape is usually sufficient. •  If the joint displacement is large or belongs to dynamic deformation joints such as bridges and tunnels, mesh TPE band must be selected.     Frequently Asked Questions   Q1: Is TPE Band chemical resistant? A: Yes, it has excellent resistance to alkalis, bitumen, diluted lye, slightly acidic solutions and salt solutions.   Q2: How is TPE Band installed? A: Can be installed by hot-air welding or cold-welding with specialized adhesives. Butt joints between two strips must be overlapped at least 5cm and bonded.   Q3: Can Mesh TPE Band be customized? A: Yes, supports color customization (blue, red, yellow, gray, etc.), width customization and size customization.   Q4: What is the service life of TPE Band? A: Mechanical reinforcement reduces fatigue damage; combined with TPE weather-resistant layer, the overall lifespan is longer than plain TPE tape; some products offer up to 20-year shelf life.   Our company not only produces Expansion Joint TPE Band, but also Cloth Duct Tape,Neon Fluorescent Gaffer Tape, Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

What is Solas reflective tape?   SOLAS Reflective Tape is a high-strength reflective material designed specifically for maritime environments, primarily used to enhance visibility in low light and harsh weather conditions. Its name comes from the International Convention for the Safety of Life at Sea, and it is an essential safety component of marine life-saving equipment.     Solas reflective tape usually adopts a multi-layer composite structure in terms of material, rather than a single material. It is mainly composed of three parts: reflective layer, substrate, and adhesive.   ◉  Reflective layer (core): This is the key to achieving high reflective performance, and there are two mainstream technologies: •  Glass microbead technology: composed of high-strength reflective glass microbeads, which achieve light return through the refraction and reflection of microbeads. Some products adopt capsule sealing structure to protect microbeads. •  Microprism technology: using tiny prism structures to reflect light, the reflection efficiency is usually higher, and the performance is more stable in humid environments. •  These reflective units are often designed as honeycomb or honeycomb structures to enhance wide-angle visibility.     ◉  Substrate (carrier): Provides support for the reflective layer, determining the flexibility, durability, and weather resistance of the tape. Common materials include: •  Polymer film: This is the most common choice, with specific materials including PET and PU (polyurethane). •  Metallized film: Coating a layer of metal (such as aluminum) on a polymer film can significantly enhance the reflective brightness. •  Cloth base : Used for occasions that require sewing, the material is soft and can be directly sewn onto fabrics such as life jackets.   ◉  Adhesive layer: used to fix adhesive tape on the surface of objects, most of which use high-performance pressure-sensitive adhesive (PSA). This adhesive has strong adhesion and durability, and can adapt to various surfaces. The types of backing adhesive include acrylic or rubber.   ◉  Release paper (protective layer): Protect the adhesive layer before use, usually made of silicone coated paper or polypropylene film     Core advantages:   •  Authoritative compliance certification: meets international maritime safety regulations such as IMO, USCG, NHTSA, etc., can help ships pass maritime safety inspections, and avoid compliance risks. •  Ultra strong wide-angle reflection: Equipped with high-performance microprism/glass bead structure, it maintains high reflectivity under multiple observation angles, and can efficiently reflect light sources from different directions in search and rescue scenes. •  Durable and sturdy: It can resist the erosion of seawater, salt spray, ultraviolet (UV) radiation, and solvents, and maintain stable performance in harsh marine environments. •  Persistent adhesion: Strong pressure-sensitive adhesive can firmly adhere to various surfaces (such as lifeboats, life jackets). •  Flexible and snug fit: The material is soft and can tightly adhere to irregular or curved surfaces. •  Clear identification: The surface is usually printed with the words "SOLAS" and rudder markings for easy recognition of compliance.   Appearance and core parameters   •  Color expression: It appears silver gray during the day and reflects bright white light when exposed to light at night, with a very long visible distance. •  Reflective performance: The reflective brightness exceeds 1000 candela, far exceeding ordinary engineering grade reflective films. •  Specification and size: The standard width is usually 50mm (5cm), and the standard roll length is mostly 45.7m (about 150 feet). •  Temperature resistance range: It has extremely strong weather resistance and is usually suitable for temperatures ranging from -30 ° C to+65 ° C. Some products have a wider tolerance range.     Application scenarios   •  Lifesaving equipment matching: widely used for contour marking of life jackets, lifebuoys, lifeboats, and rafts, greatly improving the detection efficiency during emergency search and rescue. •  Ship facility identification: pasted on deck guardrails, escape routes, emergency equipment cabinets, pilot gangways, and other locations to enhance the safety warning effect of onboard operations. •  Cross disciplinary expansion and use: In addition to maritime scenarios, it can also be used for scenarios that require high visibility signage, such as trailers, forklifts, engineering equipment, and agricultural machinery.     Frequently Asked Questions   Q1: What colors are available? A: SOLAS standard is silver (reflects white). To meet SOLAS standards, the tape must reflect white — the brightest and farthest visible color.   Q2: How long does SOLAS reflective tape last? A: 7–10 years durability in harsh marine environments, depending on sun exposure, saltwater contact, and physical wear.   Q3: How do I install SOLAS reflective tape? A: Clean and degrease surface thoroughly, dry for 2–3 min, peel liner, apply at room temperature (>10°C), press firmly with roller.   Q4: Can SOLAS tape be used on land? A: Yes. While designed for maritime use, it's also great for motorcycles, bicycles, kayaks, helmets, and any outdoor low-light visibility needs.   Our company not only produces Reflective Tape, but also Cloth Duct Tape, Gaffer Tape, Acrylic Foam Tape,Anti Slip Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

What is the anti slip grade?   There is no globally unified standard for the anti slip grade of anti slip tape, and currently there are two mainstream grading methods in the market: the European system and the American system.     European system: DIN 51130 standard (R-grade)   This is currently the most common anti slip grade standard in the domestic market. It is divided into anti-skid performance based on R values (R9-R13), with higher values indicating stronger anti-skid capabilities.   •  R9- R10: Suitable for dry indoor environments with slight slip risk, such as offices, shops, etc. •  R11: Suitable for areas with moderate slip risk, which may come into contact with water and oil. For example, factory workshops, kitchens, etc. •  R12: Suitable for areas with higher slip risk. The tape, usually in black/yellow warning colors, has a grade of R12. •  R13: The highest anti slip level, suitable for extreme environments with extremely high slip risks. For example, slopes, areas around heavy machinery, and areas with severe oil pollution.   Products that comply with this standard are usually clearly labeled, such as "anti slip grade R13, compliant with EN 13552" or "manufactured according to DIN 51130 anti slip (R group) R13 standard".     American system: NFSI and coefficient of friction (COF)   The certification system of the National Floor Safety Institute (NFSI) in the United States is another important reference. The core indicator is the static coefficient of friction (SCOF) under wet conditions. •  High anti slip standard: NFSI defines SCOF ≥ 0.60 as the "High Traction" standard. •  Actual effect: According to NFSI research, floors that meet this standard can reduce slip accidents in humid environments by 50% to 90%.     Application scenario division   According to the wear resistance and anti slip grade, the selection and application of adhesive tape are as follows:   •  Industrial and Heavy Duty Environment (R12-R13/Heavy Mineral Sand) Used for factory assembly line pedals, warehouse loading and unloading ramps, forklift access, steel structure ladders, ship decks, etc. This type of scenario involves oil stains, iron filings, or heavy crushing, requiring thick substrate and large particle alumina tape, often accompanied by black and yellow warning strips. •  Commercial and Public Places (R10-R11/Medium High COF) Used for mall stairs, hospital corridors, school walkways, hotel bathing areas, and underground garage ramps. Pay attention to balancing walking comfort and safety, choose waterproof and mildew proof models for wet and slippery areas, and choose fluorescent/reflective guidance for emergency evacuation in dark areas. •  Home and skin friendly scenes (no sand PEVA or fine sand) Used for shower room floors, bathtub edges, wooden staircase steps, balconies. When walking barefoot, it is necessary to avoid coarse particles that may cause discomfort to the feet. Soft PEVA sand belts or fine quartz sand belts should be used more often, which should be non-toxic, mold proof, and tear off without damaging the original ground. •  Transportation and Special Equipment Used for car pedals, crane maintenance ladders, and fitness equipment (treadmills/skateboards). Most of them are aluminum foil flexible substrates that need to adhere to curved surfaces and withstand certain temperature differences.   When making a purchase, it is recommended to first consider the substrate: PVC+mineral sand for outdoor/heavy industry, aluminum foil base for irregular surfaces, and PEVA sand free for barefoot areas; Before construction, it is necessary to ensure that the ground is free of oil and dry, and if necessary, apply primer to prevent edge warping.   Frequently Asked Questions   Q1: How to choose the right slip-resistance rating based on the environment?   When choosing anti slip tape, the risk of slipping in the usage environment should be evaluated first: •  Dry and low-risk environments (such as offices and shops): R9 grade can be selected. •  Environments that may come into contact with water or oil stains (such as kitchens and workshops): It is recommended to choose grades R10 to R13. •  High slippery, high-risk or inclined surfaces (such as industrial heavy oil areas, slopes): The highest grade of R12 or R13 should be selected.   Q2: Can anti-slip tape be used on wet or low-temperature surfaces?   Before pasting, it is necessary to ensure that the surface is completely clean and dry, otherwise it will affect the adhesion of the tape. At the same time, construction should be avoided at temperatures that are too cold or too hot to affect the curing effect of the adhesive.   Our company not only produces Anti Slip Tape, but also Acrylic Foam Tape,Screen Repair Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

What is the best anti slip tape to stick in the bathroom?   The bathroom space is narrow and the floor is slippery, making it a high-risk area for slip accidents in the home. Therefore, anti slip bathroom is an essential part of home safety that cannot be ignored. Applying anti slip tape is a good option to prevent slipping in bathrooms and bathtubs.   When choosing bathtub anti slip tape, the main considerations are the anti slip effect, adhesion strength, durability, and whether it is easy to clean.   The material of bathroom anti slip tape varies greatly in terms of its effect and experience. I have compiled the characteristics of several mainstream materials, you can compare and see which one is more suitable for you:   ◉ Material comparison:   •  Diamond sand (mineral particles): The surface is rough diamond sand particles, with extremely strong anti slip effect and very wear-resistant. But the foot feels too hard and may not be suitable for fully barefoot areas. Suitable for key anti slip positions such as shower area entrances and exits, inside and outside bathtubs, especially recommended for families with high anti slip requirements (such as elderly and children).   •  Rubber: Balancing slip resistance and comfort. The material is soft and elastic, with a good foot feel, and the anti slip effect becomes more stable when exposed to water. Usually durable and less prone to warping. Suitable for places such as inside and outside bathtubs, shower rooms, etc. that require barefoot stepping, balancing safety and comfort.   •  PVC (polyvinyl chloride): a cost-effective choice. Affordable price, diverse styles, good flexibility, able to fit slightly uneven surfaces. However, the anti slip effect and durability are generally not as good as diamond sand and rubber, and some products may age and harden in humid environments. Suitable for budget constraints or as a short-term transition plan.   •  Silicone: Emphasize texture and durability. The material is environmentally friendly and skin friendly, with good anti slip properties, high temperature resistance, and is not easily aged. The surface does not leak water and is not prone to mold. But the price is usually higher, and the anti slip effect is highly dependent on the quality of the adhesive backing. Suitable for families who pursue high quality, long lifespan, and sufficient budget.   •  PEVA: a skin friendly and environmentally friendly choice. This is an environmentally friendly material that does not contain harmful substances and is skin friendly, making it very suitable for scenarios that require skin contact. If you have high requirements for material environmental friendliness and skin texture, you can pay attention to this option.     •  PET/PP: As a base material, it is often used in combination with other anti slip layers. The characteristics are durability, waterproofing, and corrosion resistance.   ◉ How to choose?   When faced with different materials, you can refer to the following ideas to make quick decisions:   •  Pursuing ultimate safety: Choose diamond sand material, which has the most reliable anti slip performance. •  Value comfortable foot feel: PEVA,Rubber and silicone are better choices, and stepping on them barefoot is more comfortable. •  Budget limited: PVC has the lowest price, but it is acceptable that its durability may be slightly inferior. •  Hope to be beautiful and invisible: You can choose transparent silicone or PVC tape that can blend seamlessly with the tiles. •  If there are elderly or children at home, it is recommended to use them in combination in key areas, such as using diamond sand in the shower area and rubber,PEVA or silicone in other barefoot areas, to achieve the best protective effect.       ◉ Frequently Asked Questions   Q1: Where is the anti slip tape attached? Stick it in the most slippery key position: •  Entrance and exit of shower area •  Inside and outside of bathtub •  In front of the washbasin •  Inside the bathroom entrance   Q2: How to install anti slip tape correctly? •  Thoroughly clean: Use a neutral cleaner to wipe the floor clean, thoroughly removing oil, soap, and dust. •  Completely dry: You must wait for the ground to completely dry before sticking, moisture is the biggest enemy of stickiness. •  Cutting and pasting: Cut the tape to the appropriate length, and cut the corners into rounded corners to prevent warping. Tear off the backing adhesive, apply pressure while sticking, and expel bubbles from the inside out. •  Static curing: After pasting, wait for at least 4 hours (preferably overnight) before using or soaking in water.   Q3: How long can anti slip tape be used? High quality anti slip tape can last for 1-2 years under normal use. It is recommended to check the edges monthly for any warping or aging.   Q4: Is anti slip tape suitable for all floors? Suitable for smooth and flat ceramic tiles or stone surfaces. Not suitable for rough, cracked, or uneven surfaces exceeding 3mm.   Q5: Does it hurt to step on non slip tape barefoot? The diamond material has coarse particles, which some people may find uncomfortable. PEVA, Rubber or silicone material provides a softer and more comfortable foot feel, making it more suitable for areas where bare feet step on.   Q6: How to clean anti slip tape? Rinse with clean water for daily use. If there is dirt, use a soft brush dipped in neutral detergent to gently brush. Avoid using bleach or strong acid cleaners to prevent damage to the tape.   Our company not only produces Anti Slip Tape, but also Cloth Duct Tape, Gaffer Tape, Acrylic Foam Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

How to choose industrial anti slip tape   The selection of industrial anti slip tape is mainly based on the specific usage environment, pedestrian flow, and functional requirements, to match the key properties of the tape such as material, roughness, and adhesion. It is a comprehensive assessment related to safety and compliance.   Step 1: Clarify your specific needs Before making a selection, it is important to clarify the following questions to make the selection more targeted: • Where to paste it? Ground, stairs, ramps, equipment or rollers? • What is the surface material? Concrete, metal, wood, ceramic tiles, or plastic? Do you need to stick it on uneven surfaces? • What are the environmental conditions like? Indoor or outdoor? Is it damp, oily, exposed to chemicals, or subjected to extreme temperatures? • Expected foot traffic or usage intensity? Is it for personnel to walk, or will there be heavy equipment such as forklifts passing through? • What is the main purpose? Is it just anti slip, or does it need to serve as a warning, guidance, or protective device at the same time?   Step 2: Understand the core components The performance of industrial anti slip tape is determined by its structure and materials. ◉ The backing determines the overall strength, flexibility, and weather resistance of the tape. • PVC (polyvinyl chloride): the most common, cost-effective, flexible and durable, suitable for most indoor and outdoor environments. The disadvantage is that it may become brittle at low temperatures. • PET (polyester): More durable than PVC, wear-resistant, tear resistant, and heat-resistant, suitable for high-strength and high demand places. • Rubber: It has a high coefficient of friction and is extremely durable, suitable for heavy loads and harsh environments. • Aluminum foil: very durable, corrosion-resistant, suitable for environments with extreme high temperatures or chemical exposure. • PEVA: Made of soft and environmentally friendly material, it can directly contact the skin and is commonly used in barefoot areas such as bathrooms and swimming pools. ◉  Abrasive Surface - Provides direct friction. Common ones include: • Aluminum oxide particles: the most commonly used high hardness abrasive with excellent and long-lasting anti slip effect. • Mineral particles: also provide strong grip and are commonly used in heavy-duty tape. • Rubber/Dark Texture: Anti slip through textures such as dragon scales and diamond patterns, with a relatively soft texture that does not harm the skin. ◉  Adhesive - determines the firmness of the bond. • Acrylic: The most common type, with strong adhesion, weather resistance, water resistance, and chemical resistance, widely used. • Rubber: With high initial viscosity, it is suitable for sticking to uneven or porous surfaces. • Silicone: Used for special purposes such as high temperature resistance or when non stick surfaces are required. • Key indicators: You can focus on peel strength (the higher the value, the stronger the viscosity, heavy industry requires ≥ 15 N/cm) and holding time (testing long-term stability).   Step 3: Match application scenarios and make key choices According to your specific needs, match from the following dimensions: Key considerations Selection Recommendations Environment and Intensity Indoor dry environment Standard PVC or PET tape is sufficient Damp, oily or outdoor environment Choose waterproof, oil resistant, and UV resistant products High traffic volume or heavy machinery passage Heavy Duty tape must be used, as it has coarser abrasives and thicker substrates Extreme temperature Check the temperature resistance range of the product, such as -10 ° C to+50 ° C or -5 ° C to+80 ° C Function and Safety Warning of hazardous areas Choose yellow and black warning tape Dim environment Fluorescent or light storage tape can improve visibility Maintain a beautiful and inconspicuous appearance Select transparent tape surface characteristics Smooth surface (metal, ceramic tile) Standard acrylic adhesive is usually sufficient Rough or porous surfaces (concrete, wood) Rubber adhesive or primer may be required for use Anti slip grade Refer to DIN 51130 standard,and industrial grade anti slip tape can usually reach R13 level (the highest anti slip level)   Step 4: Pay attention to performance parameters and brand certification • Check technical parameters: In addition to the above materials, attention should also be paid to the total thickness, tensile strength, fracture elongation rate, etc., which determine the physical strength of the tape. • Prioritize certified products: Choose brands that have been certified by independent safety organizations (such as the National Floor Safety Institute (NFSI) in the United States) or meet international safety standards (such as OSHA), as this ensures quality and safety. • Trust well-known brands: Famous brands such as 3M, tesa, Jerrytape, etc. are usually more reliable in quality control and performance.   Step 5: Proper Construction and Maintenance • Surface treatment: Ensure that the adhesive surface is dry, clean, free of oil stains and dust. Cleaning agents can be used to clean oil stains. • Construction temperature: The optimal construction temperature is usually above 10 ℃, and for some products, it is recommended to use 20-30 ℃. • Pasting technique: When cutting, round the edges to prevent warping. After pasting, use a rubber roller or hammer to compact and eliminate bubbles. The adhesive strength usually reaches its optimum after 72 hours. • Regular inspection: Regularly check whether the edge of the tape is raised or worn, replace it in a timely manner, and ensure safety.   Choosing industrial anti slip tape is essentially choosing a precise risk solution for your work environment. Starting from a clear requirement and gradually matching the most suitable product is the most effective way to ensure safety.   What specific scenario are you planning to use it in? For example, on the factory floor, stairs, or equipment? If it's convenient for you to tell me the specific surface material and environmental conditions, as a professional anti slip tape manufacturer, Jerrytape can help you make more specific recommendations.    

What are rug & mat grippers? RUG&MAT Grippers "is a small household tool used to secure carpets and door mats, preventing them from sliding or curling on smooth surfaces. They are also commonly known as carpet anti slip stickers, carpet fasteners, or carpet clasps.   ◉ Its core functions and advantages include:   •  Anti slip and anti fall: This is the most important function. It can effectively prevent carpets or door mats from sliding on hard surfaces, avoiding tripping and slipping accidents caused by carpet displacement. This is particularly important for families with children, elderly people, or pets. •  Protecting the ground and carpet: On the one hand, it can serve as a buffer layer to prevent rough materials on the back of the carpet from scratching wooden floors, tiles, etc; On the other hand, it can fix the corners of the carpet, prevent curling and wear, and extend the service life of the carpet. •  Maintain aesthetics: It can ensure that the carpet is flat and wrinkle free, making the home environment look neater. •  Easy to use: Installation is very simple, usually just "peel off the backing glue, stick it on the back of the carpet, and then press it down". And most of them can be washed with water and reused.   ◉ Common forms:   •  Adhesive anti slip sticker •  The entire anti slip pad •  Magnetic fastener   ◉ Steps to use:   •  Ensure that the back of the carpet and the floor are clean and dry. •  Remove the release paper from the back of the fastener. •  Stick the fixator on the four corners or edges of the back of the carpet. •  Return the carpet to its original position and press firmly on the fixture to ensure a tight fit with the ground.   ◉ Notes:   •  Suitable for flooring: Most products are suitable for hard flooring such as wooden floors, tiles, marble, etc. •  Is it washable: Please confirm whether the product is washable and reusable before purchasing. •  Place of use: Most products are designed for indoor use. If you want to use it outdoors, you need to choose a product labeled "Outdoor".   Our company not only produces RUG&MAT Grippers, but also Cloth Duct Tape,Neon Fluorescent Gaffer Tape, Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.  

Which is better, nano tape or double-sided tape?   There is no absolute answer to this question, it mainly depends on what you want to use it for.   •  If you want to hang heavy objects, leave no traces, and want to use them repeatedly, then nano tape is better. •  If you are only temporarily fixing light items such as paper, envelopes, or pursuing low cost, then regular double-sided tape is sufficient.       The main differences between the two can be referred to in the table below:   Characteristic Nano tape Traditional double-sided tape Core advantages Highly adhesive, tear off without any marks, can be washed with water and reused Cheap price, wide variety, and versatile applicability Material and appearance Transparent gel shaped, with certain thickness Various types (such as cotton paper, foam, PET, etc.), mostly white or semi transparent Adhesive strength Very high, especially on smooth surfaces, the shear strength can reach 0.5-1.0 MPa Medium to high, depending on the specific type Is there any residual glue Basically without leaving any traces, the colloid has strong integrity and is not easily broken or left behind Easy to leave adhesive marks and difficult to clean Reusability Washable and reusable, but not recommended for "ten thousand uses" Non reusable Applicable surface Smooth surfaces (such as tiles, glass, metal, smooth wooden boards) have the best effect Widely applicable, some types can fill slight uneven surfaces Not applicable to surfaces Rough, peeling, and uneven walls (such as lime walls, latex paint walls) Depending on the specific type Price Relatively expensive Very cheap Typical use Fixed power strip, hanging photo frame, storage data cable, car accessories, seamless hook Office work, manual labor, paper pasting, fixing lightweight items, packaging, etc       How to choose?   ◉  Choose 'Nano Tape', if: •  You need to hang things on smooth surfaces (tiles, glass, metal). •  You hope to leave no traces and protect the wall. •  You are willing to pay a slightly higher price for convenience and reusability. •  Typical scenarios: fixing a toothbrush holder on bathroom tiles, sticking hooks on smooth walls in the kitchen, and posting sticky notes on glass partitions in the office.   ◉  Choose 'traditional double-sided tape', if: •  You pursue the ultimate cost-effectiveness, it's just a temporary fix. •  The pasting surface is not very smooth or has slight texture. •  What you need is for regular purposes such as office work and manual labor. •  Typical scenario: Pasting paper, photos, handmade, temporarily fixing items.     Our company not only produces Nano tape, but also Cloth Duct Tape,Neon Fluorescent Gaffer Tape, Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.                                  

How to install Pool Rubber Grip Tape?   Pool Rubber Grip Tape is a high-performance anti slip material that firmly adheres colored EPDM (ethylene propylene diene monomer) particles to a tape substrate. This tape has a comfortable foot feel, is skin friendly and does not prick the feet. It is non slip and can cushion, environmentally friendly and non-toxic, extremely durable, and suitable for outdoor use. Therefore, it is very suitable for use in damp, barefoot areas such as poolside, bathroom, kitchen, etc. It is also commonly found in public areas such as school stairs and hospital corridors that require anti slip and noise reduction.     In order to achieve better performance of this tape, correct installation is crucial. The construction standard process is summarized as follows:     1.Thoroughly clean the surface (crucial!) This is the most important step in ensuring a firm adhesion. The construction surface must be thoroughly cleaned, completely dry, and free of oil and wax. •  Use a cloth with neutral cleaning agent to vigorously wipe away dirt, algae, or old adhesive residue on the surface. •  For oil stains, it is necessary to thoroughly clean them with degreasers or isopropanol. •  After rinsing with clean water, make sure the surface is completely dry and free of any moisture.   2. Measurement and cutting •  Measure the length to be pasted with a tape measure and cut it with a utility knife or scissors. •  Key technique: Trim rounded corners. Be sure to cut the four corners of the tape into rounded corners instead of right angles. This is a crucial step in preventing the corners from warping or falling off due to trampling in the future.   3. Tear off the backing paper and stick it on •  Tear off the release paper (backing paper) on the back of the tape. Be careful not to touch the exposed adhesive surface with your fingers as much as possible to avoid affecting the adhesion. •  It is recommended to first tear off the 3-4 inch (approximately 7-10 cm) backing paper on one end, position and paste it, and then peel off the remaining backing paper while flattening the tape.   4. Apply force to compact and expel bubbles This is the key to ensuring that the tape is fully adhered to the surface. •  After pasting, use a rubber roller, rubber hammer, or hard plastic scraper to roll or tap vigorously from the center of the tape to all sides. •  This action can effectively expel the air under the tape, making it tightly adhere and avoiding the formation of bubbles.   5. Closing and maintenance •  Optional) Edge sealing: If the humidity at the edge of the swimming pool is high or there is a large flow of people, a special edge sealing adhesive (such as acrylic resin type) can be applied to the edge of the tape to effectively prevent moisture and dirt from infiltrating and prevent edge curling. •  Static curing: After construction is completed, it is recommended to wait for at least 24 hours for the tape to fully cure. During this period, avoid contact with moisture or heavy pressure on the tape.     Installation precautions   •  Construction temperature: It is recommended to carry out construction in an environment above 10 ℃, as low temperatures can affect the adhesion of the backing adhesive. •  Surface requirements: Adhesive tape is most suitable for sticking on smooth and flat surfaces (such as tiles, metal, hard plastic). If the surface is rough or has cracks, it may be necessary to apply a specialized primer first. •  Installation timing: It is necessary to install in a completely dry state in the swimming pool or on the ground.       Our company not only produces Pool Rubber Grip Tape, but also Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

1.What is acrylic double-sided tape?   Acrylic Double Sided Tape is a pressure-sensitive adhesive tape mainly composed of acrylic polymer. It is usually composed of release film and acrylic adhesive layer, and some models may add foam substrate to enhance shock absorption and gap filling ability. Compared to traditional double-sided tape, its molecular structure is more stable, which not only enables high-strength bonding, but also resists ultraviolet radiation, moisture, and chemical erosion.     2.Core advantages and disadvantages   Advantage Shortcoming •  High adhesion and durability: Strong initial adhesion, able to quickly generate high adhesion and maintain stability for a long time, not easy to peel off. •  Excellent weather resistance: able to maintain stability in the temperature range of -20 ℃ to 120 ℃, resistant to ultraviolet rays and moisture. •  Transparent and traceless: Most designs are fully transparent,(Available in gray, white, and black), with a clean and residue free surface after tearing, without affecting aesthetics. •  Suitable for multiple materials: Good adhesion to metal, glass, plastic, wood, and painted surfaces. •  High price: The unit price is usually several times that of ordinary double-sided tape, making it more suitable for long-term use or load-bearing scenarios. •  High requirements for surface smoothness: On rough or porous surfaces (such as unpainted cement walls), the adhesion will be greatly reduced. •  Extremely low temperature brittleness: When the ambient temperature is too low, the colloid will become hard and brittle, resulting in a significant decrease in initial adhesion.     3.Common application scenarios   •  Home decoration Used for installing wall hooks, bathroom mirrors, kitchen shelves, and baseboards without drilling holes. Its waterproof and moisture-proof properties enable it to remain stable even in humid environments.   •  Automotive Interior Widely used for fixing car phone holders, center console ornaments, car body decorative strips, and engine compartment pipelines, it can withstand temperature changes and vibrations inside the car.   •  Digital electronics Suitable for the cushioning and bonding of laptop shell borders, screen modules, and shells, as well as temporary positioning and auxiliary fixation of various precision components.   •  Advertising sign The installation of acrylic directional signs, signage, and outdoor light boxes for shopping malls and offices can ensure firmness and achieve visual invisibility.     4.FAQ:   Q: Can it really be completely traceless? A: It can achieve seamless removal on dense and smooth surfaces such as glass, ceramic tiles, and metal. But on porous materials (such as partially unpainted wood, cement walls) or soft textured PVC, colloids may penetrate into micropores or damage the coating, posing a risk of leaving marks.   Q: How to paste to achieve maximum strength? A: It is necessary to ensure that the surface is clean and dry, and it is recommended to wipe it with alcohol; After pasting, use a scraper to press firmly to expel the air; Do not touch water or hang heavy objects within the first 24 hours of pasting. The maximum structural strength can be reached after 72 hours.   Q: What if it's too cold in winter and doesn't stick firmly? A: When the temperature is below 10 ℃, the initial viscosity of the colloid will significantly decrease. It is recommended to use a hair dryer to heat the adhesive surface slightly and activate its stickiness, or raise the indoor temperature to above 15 ℃ before construction.   Our company not only produces Acrylic Double Sided Tape, but also Cloth Duct Tape,Neon Fluorescent Gaffer Tape, Gaffer Tape, Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

What is EPDM rubber particle anti slip tape?   EPDM rubber particle anti slip tape (commonly known as EPDM anti slip tape or swimming pool anti slip tape) is a functional anti slip material with EPDM colored rubber particles and elastic substrate as the surface, and high-strength water-resistant acrylic backing adhesive as the bottom. It is different from ordinary PVC or diamond sand (alumina) anti slip tape. Product Composition   •  Surface layer: Made by pressing EPDM colored rubber particles, the texture is soft and elastic, comfortable to walk barefoot, and the particle texture provides wet friction. •  Substrate layer: usually made of tear resistant fabric/elastic sheet, endowed with certain tensile and deformation resistance. •  Back adhesive layer: coated with strong water-resistant acrylic adhesive, which can firmly adhere to flat surfaces such as tiles, concrete, metal, and wooden boards (it is recommended to use a primer/adhesive aid in humid environments).   Product Highlights   •  Soft and comfortable: The surface of EPDM particles is softer than diamond sand tape, making it suitable for walking barefoot in wet areas without hurting your feet. •  Wet anti-skid: The grain texture increases friction, and it maintains good anti-skid performance even when exposed to water or slight oil stains. •  Weather resistant and aging resistant: UV resistant, ozone resistant, high and low temperature resistant (-50~130 ℃), long-term outdoor use will not fade or crack. •  Shock absorption and noise reduction: With elasticity, it can cushion foot pressure and reduce walking noise. •  Environmentally friendly and durable: non-toxic and odorless, resistant to chlorine water and weak acid and alkali, strong adhesive backing, wear-resistant and long service life.   Product Application   •  Wet and slippery areas: swimming pool shore, changing room, shower room SPA、 Bathroom and kitchen operating area. •  Public/Commercial: Stairway corridors in schools/kindergartens, rehabilitation centers in hospitals, nursing homes, hotel lobby ramps, entrance steps to shopping malls. •  Outdoor/Sports: Outdoor stairs, ramps, fitness trails, amusement park surroundings, ship decks, etc.   EPDM rubber particle anti slip tape is a weather resistant self-adhesive anti slip tape with elastic EPDM particle surface, designed for barefoot walking in wet areas and outdoor pedestrian ramps/steps, balancing comfortable stepping and wet anti slip.     Our company not only produces Anti Slip Tape, but also Acrylic Foam Tape,Screen Repair Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

What are the advantages of the Mesh TPE expansion joint Band?   The core advantage of Mesh TPE expansion joint band lies in its "mesh reinforcement structure", which is like adding "bones" to ordinary TPE waterproof tape, making its performance far superior to ordinary TPE tape when dealing with complex and large displacement.     The main differences between the two can be summarized as follows:   Dimension Plain TPE Band Mesh TPE expansion joint Band Tensile Strength Relying solely on TPE body, it is prone to necking and thinning under tension Polyester mesh bears the main tensile force, increasing tensile strength by 30%~50%+, and does not break under large displacement Tear Resistance Nails/sharp angles can easily cause tearing and expansion Grid locks cracks to prevent propagation, with significantly better puncture and tear resistance than pure TPE Creep Resistance Easy to relax and creep under long-term sustained tension Grid restricts the slip of polymer chains, resulting in smaller permanent deformation and better elastic recovery after repeated expansion and contraction Installation Durability Tearing, trampling, and pulling are prone to damage The grid distributes stress, making it less prone to tearing or accidental tearing during bonding/hot air welding  Movement Capacity Suitable for small and medium-sized seam displacement Can withstand greater cyclic displacement (± 25%~50% joint width), suitable for dynamic deformation joints in bridges/pipe galleries Dimensional Stability Due to heat or stress, it is prone to local bulging and twisting Grid constraint lateral contraction and expansion, flat and not warped after pasting Fatigue Life Dependent on TPE weather resistance Mechanical enhancement reduces fatigue damage and, when combined with TPE weather resistant layer, results in a longer overall lifespan   Plain TPE Band rely on elastic sealing but have limited mechanical strength. They are prone to tearing, elongation, and failure when subjected to large displacement, strong pulling, or sharp base surfaces; The mesh reinforced type with built-in high-strength polyester mesh suppresses tearing and creep, making it particularly suitable for large displacement and high demand expansion joints in bridges, tunnels, underground pipe galleries, etc. It is an upgraded solution for ordinary TPE tapes.     Our company not only produces Expansion Joint TPE Band, but also Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.                                        

What does butyl tape not stick to?   Butyl Tape is a non curing, high viscosity waterproof sealing tape that has good adhesion to most metals, concrete, glass, PVC, etc. However, it is prone to non stick or extremely poor adhesion on the following surfaces:   1、 Non adhesive or difficult to adhere materials/surfaces •  Low surface energy plastics: PE (polyethylene), PP (polypropylene), PTFE (PTFE) •  Surface leakage of oil, silicone oil, release agent, and asphalt oil •  Powdered, sanding, and loose surface layer •  Clear water, frozen water, continuous soaking on the water surface •  Severe powdering of old paint surface layer   2、 General methods for improving bonding effectiveness •  Cleaning: Use a dry cloth/alcohol to remove dust, oil stains, and silicone oil •  Polishing: Difficult to stick surfaces other than PE/PP can be lightly polished to increase roughness •  Primer: For extremely difficult to stick surfaces, specialized primer/primer can be used (recommended by many manufacturers) •  Rolling: After pasting, press firmly to expel air •  Avoid low-temperature construction (<5 ℃, poor flowability of butyl, affecting infiltration)   Our company not only produces Butyl Rubber Tape, but also Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Screen Repair Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

How does detectable tape work?   Detectable underground warning tape (also known as tracer tape, detectable warning tape) is mainly used in the construction of buried gas, water, communication, power and other pipelines. It is laid about 30-50cm directly above the pipeline and does not transmit signals, but works in conjunction with metal detectors/pipeline detectors.       Working principle: The tape contains a continuous metal conductor (usually tin plated copper wire, stainless steel wire, or aluminum foil tape).   1.Lay Lay detectable warning tape in parallel above underground pipelines (PE pipes, PVC pipes, cables, etc.). Adhesive tape is usually in bright colors (yellow for gas, blue for water supply, red for electricity, etc.), with warning signs such as "Multiple pipelines are strictly prohibited from excavation" printed on it.     2.Detect Using metal detectors or pipeline detectors (transmitter+receiver) on the ground: If the active signal method is used, sometimes the construction party will apply electromagnetic signals (clamps or direct connections) on the metal wire, and the detector can accurately locate it. If only passive detection is used: the high-sensitivity metal detector can directly sense the presence of metal wires and prompt "there are buried objects below" to prevent blind excavation. Scanning along the direction can roughly determine the pipeline direction and burial depth range.   3.Dual function of warning and positioning When excavating mechanically, first excavate to the colored warning tape → remind to stop work and switch to manual excavation. Even if it is not excavated (deeply buried or covered), instruments can be used to detect the position of its metal layer in advance.   Our company not only produces Underground Detectable Tape, but also Cloth Duct Tape,Neon Fluorescent Gaffer Tape, Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

What is the difference between warning tape and caution tape?   According to OSHA and ANSI standards, the essential difference between Warning Tape and Caution Tape lies in their level of danger.     •  Caution Tape: Represents "Caution". For mild risk, it means that if not careful, it may cause minor or moderate injuries. •  Warning Tape: Represents "Warning". Between "caution" and "danger", for moderate to severe risks, it means that it may lead to serious injury or even death.   ◉  Caution Tape: Walk slowly with caution •  Applicable scenario: Remind people to "walk slowly, don't trip up". Usually used for wet and slippery                 surfaces, temporary maintenance areas, or minor obstacles. •  Common representative styles: -- Yellow background black lettering tape: the most common style, printed with the words "CAUTION", used to      remind potential physical hazards. -- Yellow and black stripes: The classic "zebra crossing" tape has a strong visual impact and is specifically           used to mark places that are prone to tripping or hitting the head.     ◉  Warning Tape: Dangerous entry prohibited •  Applicable scenario: Tell people 'It's dangerous ahead, don't wander around'. Usually used for high-altitude       operations, areas around heavy machinery, or areas with a risk of falling. •  Common representative styles: -- Orange background black letter tape: a standard "Warning" warning tape used in medium to high-risk               areas,  which is more serious than ordinary warning tape. -- Orange and white stripes: commonly used in road traffic or construction maintenance sites, emphasizing         the presence of heavy equipment or engineering operations ahead.   •  If there are fatal hazards such as high voltage electricity and deep pits on site, please use the red and white Danger Tape directly, which is the highest level of blockade.   Our company not only produces Caution Tape, but also Cloth Duct Tape,Gaffer Tape, Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

What surfaces can Gaffer Tape be applied to?   Gaffer Tape (stage/matte cloth tape) can firmly adhere to various materials such as wood, metal, glass, stone, plastic, carpet, fabric, leather, etc. due to its high initial adhesion, easy to tear, non reflective, and minimal removal of residual adhesive.   Suitable for adhesive surfaces   Surface type Typical example Fabric/Leather Stage curtains, carpet edges, performance costumes, camera straps Metal Lighting stand, photography tripod, aluminum alloy equipment (when dry and oil-free) Plastic (hard plastic) Camera body shell, microphone clip, PVC cable tray Wood/Wood Flooring Fixed cable routing on stage wooden floor Paper/card board/foam board Marking stations and temporary fixed props Painted wall/stage floor Temporary fixed cable (high-quality gaffer tape has almost no residue after short-term use)       Poor adhesion effect or not recommended   •  Low surface energy plastics:such as polyethylene (PE) and polypropylene (PP), are difficult to adhere and       prone to detachment. •  Very rough/porous surface: untreated cement walls, brick walls - small contact area, poor adhesion. •  Dust/oil stains/damp surfaces: Any tape will significantly reduce adhesion. •  Long term outdoor exposure: UV exposure can cause the fabric to age, become brittle, and leave residue         difficult to clean (it is not an all-weather outdoor tape).     Our company not only produces Gaffer Tape, but also Cloth Duct Tape,Neon Fluorescent Gaffer Tape, Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

What scenarios can Gaffer Tape be used in?   The biggest difference between "Gaffer Tape" (matte cloth tape/photographic tape) and regular glossy cloth tape is that the surface is matte, non reflective, leaves no residue (high-quality version), and easy to tear.   The typical usage scenarios are as follows:   ◉  Film and Television/Photography/Stage •  Fixed cables: Stick the light/microphone/power cables to the floor to prevent tripping, and the matte surface     will not reflect in the lens. •  Wire bundling and management: Temporary bundling of equipment wires, with minimal residue left after           tearing off. •  Temporary repair/shading: covering reflective points, fixing soft light paper/color chips, temporarily fixing           props. •  Marking position: On stage, mark the actor's position/equipment placement point (matte surface that can be    used for writing).     ◉  Performance/Conference/Exhibition •  AV equipment wiring: fixed audio and video cables on the carpet of the conference room/booth. •  Temporary fixed decoration: fixing the edges and corners of the background panel, identification, and carpet     flanging. •  Microphone fixation: Some models can be used to secure the lavalier microphone to clothing (please note       skin sensitivity).      ◉  Daily/household/handmade •  Temporary repair: repairing fabric items such as tents, bags, stage curtains, etc. •  Cable management: Temporary fixing of computer/desktop cables on the legs or back of the desk. •  Tag/Category: Can be used to write temporary labels on tape.     Our company not only produces Gaffer Tape, but also Cloth Duct Tape,Neon Fluorescent Gaffer Tape, Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

What is the main purpose of duct tape?   Duck Tape is typically a three-layer composite structure,   •  The first layer: made of polyethylene resin, its main function is to provide waterproof, wear-resistant, moisture-proof and dustproof protective properties. •  Second layer: Cloth base layer, core skeleton layer, usually made of gauze fibers treated with PE resin, commonly used materials include cotton cloth, polyester fiber, nylon cloth, polyester cloth or PET cloth, etc; This layer endows the tape with tear resistance and tensile strength, allowing it to be torn by hand while maintaining a straight tear edge, while also providing the tape with a certain degree of flexibility to adhere to irregular surfaces. •  The third layer: adhesive layer, mainly using rubber pressure-sensitive adhesive with natural rubber as the main body. This layer ensures stable and long-lasting high adhesion of the tape on surfaces of various materials.   Duct Tape is a high-strength, high adhesive waterproof tape used in various fields such as industrial production and daily maintenance. Its core applications are as follows:   1、 Core industrial and professional scenario usage   •  In the field of packaging and transportation: it is mainly used for sealing heavy-duty cardboard boxes, bundling large goods, and waterproof packaging. Compared with ordinary tape, it has stronger adhesion and tensile strength, which can prevent loose and damaged packaging during transportation. •  Decoration and Engineering Scenarios: Used for carpet joint assembly, ground protection, wall painting and masking, as well as sealing and repairing pipelines, fixing and wrapping them. High temperature models can also be used for floor heating and steam pipeline protection to reduce heat loss and leakage risks. •  In the fields of manufacturing and maintenance: it is widely used in the automotive industry, papermaking industry, and electromechanical industry for waterproof protection of car cabins, chassis, and cabinets. It is also used for bundling and protecting car wiring harnesses, painting shielding, and can be used for temporary equipment fixation, marking, and shielding protection for sandblasting operations. •  Specially demanding fields: can be used for emergency equipment repair in aerospace, shipbuilding, and military fields   2、 Daily life and civilian use •  Home emergency repair: It can temporarily repair loose table and chair legs, lift carpet edges, seal air leakage gaps in doors and windows, repair damaged household items, toys and clothing, and is a convenient emergency repair tool. •  Identification and layout: Rich colors can be used as regional signs and warnings, and are also commonly used for carpet splicing and booth layout in exhibitions and stages. •  Organizing and organizing: It can bundle and organize messy wires, divide storage areas, fix loose curtains, etc., with strong practicality.   3、 Creative expansion purposes •  With its good adhesion and easy cutting characteristics, it is also often used by DIY enthusiasts for handmade creative production, making various shapes, decorations, handmade accessories, etc.   Our company not only produces Duct Tape, but also Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

What kind of tape will stick to the road surface?   The tape that can stick to the road surface is not ordinary tape, but "special engineering tape". They have special designs in terms of viscosity, weather resistance, wear resistance, and rolling resistance, mainly divided into two categories: road marking and road repair.     We will now classify and compare different types of road tape for your reference when choosing   Type Function Material Characteristic Application Reflective/road marking tape Long term, high visibility road traffic markings Synthetic rubber, polyurethane, microcrystalline ceramic beads   -Excellent nighttime reflective performance ensures driving safety -Extremely high wear resistance and weather resistance, long service life -Convenient construction, can be prefabricated into various texts and patterns Official traffic markings such as highways, urban roads, tunnels, airport runways, etc Adhesive tape/repair tape Repair cracks in asphalt/cement pavement Polymer modified asphalt SBS、 Rubber, polyurethane   -High adhesion, good elasticity, able to adapt to road surface thermal expansion and contraction -Waterproof and anti-seepage, some products have a "self-healing" function -Strong weather resistance, suitable for environments ranging from -40 ℃ to 120 ℃ -Mostly for cold construction, tear and paste, easy to operate, traffic can be opened in 5-15 minutes Repair and preventive maintenance of road cracks, potholes, and joints Warning/marking/marking tape Ground area division and warning PVC film, rubber, etc   -Bright colors (yellow/black/red/white, etc.) used to identify warning areas or passages -Has certain wear resistance and can withstand high traffic flow of people/vehicles -Some products have reflective or anti slip functions Indoor and outdoor floors of factory workshops, warehouses, parking lots, sports venues, etc Heavy duty/wear-resistant tape Endure high-intensity crushing of heavy vehicles High strength PVC, nano modified PVC+rubber   -Capable of carrying forklifts and heavy trucks for crushing -Waterproof, oil resistant, acid and alkali resistant, easy to clean -Some products can withstand pressures of over 5 tons Heavy machinery access areas such as logistics warehouses, port terminals, and heavy industry workshops   How to choose depends mainly on the specific scenario you want to use.         Our company not only produces Pavement Marking Tape, but also Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Screen Repair Tape, Glow In Dark Tape, etc,Looking forward to working with you.

How to clean and maintain non-slip tape.   The cleaning and maintenance of anti slip tape mainly follow the principle of "gentle treatment", with slight adjustments based on the material and usage scenario. Use gentle methods for daily cleaning, clever methods for stubborn stains, and avoid using strong acids, bases, and hard brushes.     ◉  Daily cleaning •  Daily cleaning: Use a soft broom or vacuum cleaner to remove surface dust and debris. For large areas, dip a mop in neutral detergent diluted at a ratio of 1:7 to 1:10, gently wipe, rinse with clean water, and thoroughly air dry. •  Gentle wet wash: Once a week, gently scrub with warm water and neutral detergent (such as dishwashing detergent), combined with a soft bristled brush or sponge. After brushing, be sure to thoroughly rinse with clean water and completely dry or air dry to prevent residual cleaning agents from affecting viscosity.   ◉  Stubborn stain treatment •  Oil and soap stains: Spray a little white vinegar or lemon juice on the stain, let it stand for about 5 minutes, and then brush it with a soft bristled brush. In addition, mixing white vinegar and baking soda into a paste and applying it to the stain, letting it sit for 5 minutes, and then brushing it off is also a safe and effective method. •  Scale and mold stains: can be treated with a mixture of toothpaste or laundry detergent and white vinegar.   ◉  Routine maintenance •  Avoid the "forbidden zone": It is best not to use strong acids and alkalis (such as bleach, strong cleaning powder), cleaning agents containing alcohol or oily ingredients. Do not directly scratch with hard objects such as steel wire balls, hard brushes, or metal shovels to avoid damaging the surface texture of the anti slip layer. •  Cleaning suggestions for different materials: -- Universal type: Regularly clean gently with a cleaning agent and a soft bristled brush. -- PVC material: Avoid contact with organic solvents (such as banana water) and clean gently.   ◉  When will it be replaced? •  The service life of anti slip tape is usually 1 to 2 years, depending on the frequency of use and load. Once there is a significant decrease in anti slip effect due to edge warping or severe surface wear, it should be replaced in a timely manner to ensure safety.   Our company not only produces Anti Slip Tape, but also Acrylic Foam Tape,Screen Repair Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

What's the difference between PVC and PET anti-slip tape?   The most obvious difference between PVC and PET anti slip tape is that PVC is known for its cost-effectiveness and softness, making it easy to apply and suitable for home and temporary protection; PET focuses on high strength and durability, suitable for industrial heavy-duty and long-term outdoor use.     Based on the usage scenario, refer to the table below for quick decision-making:   comparison PVC anti slip tape PET anti slip tape Material characteristics Polyvinyl chloride, with a relatively soft texture Polyester film, with a tougher and harder substrate Wear resistance life Generally, long-term trampling is prone to wear and tear Extremely strong, tear resistant, suitable for high traffic volume Temperature resistance performance Generally (easily brittle at low temperatures, easily softened at high temperatures) Excellent (high temperature resistance of about 120 ℃, good low temperature resistance) Construction experience Easy to tear and adhere to curved surfaces, can be repeatedly pasted High hardness, usually requires scissors/blades for cutting, high bonding requirements Outdoor weather resistance Generally, long-term exposure to sunlight can cause yellowing and brittleness Excellent, UV resistant, not prone to aging Environmental friendliness Partially containing plasticizers, with average environmental friendliness Usually environmentally friendly, non-toxic, and odorless Price Cheap (affordable) More expensive (performance oriented) Recommended scenarios Home staircase, bathroom, temporary warning, indoor dry area Factory workshop, subway station 1, outdoor steps, heavy-duty equipment     Suggestions for scene selection:   •  Home interiors (bathroom, stairs, kitchen): PVC is preferred. The family environment has a small flow of people, PVC has sufficient anti slip performance, and is cheap with low replacement costs. Pay attention to choosing a brand with good adhesive backing to prevent glue from peeling in damp bathrooms. •  Outdoor balconies, terraces, and factory entrances: PET is strongly recommended. Suzhou is rainy, and the outdoor environment requires extremely high weather resistance for adhesive tape. PET is UV resistant and water bubble resistant, with a service life several times longer than PVC, which can avoid the trouble of frequent replacement. •  Factory workshops, warehouses, and equipment pedals: PET must be used. The industrial environment involves forklift crushing, oil pollution erosion, and high-frequency trampling, and only the thickness and wear resistance of PET can be competent.   Our company not only produces Anti Slip Tape, but also Acrylic Foam Tape,Screen Repair Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.